ConferenceVertical Divider
Attendees
Additional Information |
CN-324 ~ Unexpected Sources of Energies Weeding Through Hazardous Spectrum
CN-005 ~ Grounding System Conductors: Solid, Stranded, Bare or Insulated?
CN-010 ~ Comparison of IEC and NEMA Requirements to Ensure Proper Specification and Design of Induction Motors & Generators for Global Use - Part 2
CN-013 ~ IEEE C37.20.7 Guide for Testing Switchgear Rated Up to 52kV for Internal Arcing Faults – Important Changes to the New Edition
CN-018 ~ An Introduction to IEEE Std 1458-2017 "Recommended Practice for the Selection, Field Testing, and Life Expectancy of Molded-Case Circuit Breakers for Industrial Applications"
CN-078 ~ Technology Change Management, Assessment, and Organizational Behavior
CN-091 ~ Lifecycle Focused Considerations for the Adoption of Newer (or Smart) Technologies in Electrical Systems
CN-320 ~ Adjustable Speed Drive System Comparison - VSI and LCI for High Power Applications
CN-017 ~ A Motor Primer – The Next Generation: Permanent Magnet Machines
CN-023 ~ What You Should Expect From Your Motor Service Center When Servicing Your Motor
CN-031 ~ The Differences Between Vertical and Horizontal Motors used in the Petro-Chem Industry
CN-050 ~ Coast-Downs and Run-Ups: Understanding Vibration Responses
CN-081 ~ The Different Types of Shaft-Bonding Devices and their Effectiveness
CN-097 ~ Methods to Avoid Electrical Runout
CN-353 ~ The Value of Integrating Power and Process for the Petrochemical Industry
CN-3114 ~ Using IEC61850 for a Power Management System of an Offshore Platform
CN-036 ~ Case Study: Deployment of 200 Smart Motor Control Centers
CN-066 ~ Effective Documentation of Microprocessor Based Protective Relay Configurations
CN-073 ~ Modularization of HV GIS Substations
CN-087 ~ Introduction to the New Standards - IEEE 844.1/CSA 293.1 and IEEE 844.2/CSA 293.2 for Skin Effect Trace Heating of Pipelines, Vessels, Equipment, and Structures
CN-099 ~ Pinpointing Partial Discharge in Medium Voltage Bus Duct; Recognize, Repair, Reenergize
CN-100 ~ Analysis of PLC vs. DCS in Industrial Petrochemical Applications
CN-371 ~ Applying Continuous Monitoring & Diagnosis (M&D) to Critical Rotating Machines with No Additional Device to Install
CN-024 ~ Hardware-in-the-Loop Testing of Electrical Protection and Control Systems
CN-028 ~ Case Study: Turbine Load-Sharing and Load-Shedding System for an Australian LNG Facility
CN-033 ~ Comparative Analysis of IEC and ANSI Current Transformers in Protection Applications
CN-034 ~ Comprehensive Overview, and Comparison of ANSI vs. IEC Short Circuit Calculations - Using IEC Short Circuit Results in IEEE 1584 Arc flash Calculations
CN-039 ~ Technological Obsolescence Management of Electrical Equipment and Automation Systems
CN-057 ~ A Smart Condition Monitoring System for HV Networks with Artificial Intelligence, Augmented Reality and Virtual Reality
CN-084 ~ Monitoring & Maintenance – Installing Sensors to Monitor Equipment Improves Operational & Maintenance Performance
CN-094 ~ How to ID IoT Solutions Without Feeling Like an IDIoT: an Application Perspective
MARINE TECHNICAL SESSION
CN-359 ~ Medium Voltage Frequency Converter for ESP Applications
CN-3127 ~ A New Standard for Marine Power Distribution
CN-006 ~ Generator Differential Relay Trip on an Offshore Platform
CN-015 ~ Selection and Tests of Innovative Variable Speed Moto-Compressor Solutions for a 55MW Full Electric Off-shore Platform Maximizing Availability and Efficiency with Better Environmental Impact
CN-019 ~ Transformerless Medium Voltage Drives for Offshore Applications
CN-102 ~ Design and Implementation of Generation Control System for an Offshore Platform
CN-109 ~ Harmonic Analysis of Arcing Faults and Impacts on System Protection
CN-110 ~ When, Where, and How of Ambient Temperature in Evaluating Equipment Condition
CN-3112 ~ Experience with Fast Load Shedding Using IEC 61850 GOOSE
CN-014 ~ Cables and Cable Glands for Hazardous Locations
CN-020 ~ Cooling The Arc Flash Hot Spot
CN-029 ~ Wiring in Hazardous (Classified) Locations – Where We Came From and Where We Are Going.
CN-037 ~ High Resistance Grounding (HRG) and Adjustable Speed Drives (ASD)
CN-064 ~ Case Study: Radio Application in a Smart Grid System for a Brownfield Onshore Dispersed Oil Field
CN-076 ~ Distributed Logic Load Shed System via IEC 61850
CN-095 ~ Applying Off-the-Shelf Adjustable Speed Drives and Electric Motors – An ASD Primer (Part 1)
CN-323 ~ The Effect of Hazardous Location on Electrical Equipment Short Circuit Ratings
CN-3100 ~ Premature Failure of Large HP Motors due to Improper Field Connections
CN-022 ~ Stator Endwinding Vibration in Two Pole Motors and Generators
CN-046 ~ Protective Relay Coordination Study at a Petrochemical Complex
CN-061 ~ The Effect of Airgap on Electric Motor Performance
CN-069 ~ Energy Optimal Control In Petrochemical Processes
CN-074 ~ A Holistic Approach at Electrical Equipment Monitoring and Diagnostics At All Levels in a Chemical Plant
CN-086 ~ How New Energy Codes are Impacting Electrical Substation Designs
CN-088 ~ Calculation of Transient Torques on Motors During a Residual Voltage Motorbus Transfer
SAFETY TECHNICAL SESSION
CN-393 ~ Safety By Design - How Electrical Devices Installed in the Industry can be Designed to Enhance Personnel Safety
CN-026 ~ Demise of the Dangerous and Hazardous Multi-Grounded Neutral Distribution Systems
CN-027 ~ Failure to Follow Standard Instructions Can Lead to a Serious Incident
CN-041 ~ The Next Phase in the Evolution of Safety by Design – Digital Switchgear
CN-053 ~ Strategies for Reliable Arc Flash Detection in Low Voltage Switchgear
CN-079 ~ The Disconnect Between Electrical Safety and Electrical Accident Prevention
CN-113 ~ Reliability: The Missing Leg of the Stool
CN-114 ~ Human Performance and Safety
TRANSPORTATION TECHNICAL SESSION
CN-356 ~ Design Considerations in Selection and Sizing Turboexpander Generators for Supplemental Power Generation
CN-007 ~ Active Harmonic Mitigation - What the Manufacturers Don't Tell You!
CN-011 ~ Benefits and Drawbacks of Low Inrush Large Induction Squirrel Cage Electric Motors
CN-072 ~ Process Safety Compliance and Safety Challenges of Facilities Upgrading Existing Controls
CN-080 ~ Substations in Classified Locations, Integration of NFPA 496 Pressurization Requirements with Other Supporting Systems
CN-083 ~ Optimized PM Motor Control Using LV Drives
CN-098 ~ How to Ensure Low Vibration of 2-Pole Motors on Flexible Foundations
CN-103 ~ MV Motor Optimization
|
|